How to Record Two People with RØDE Wireless ME

Choose between two valid workflows

You can record two people with RØDE Wireless ME in two ways. Use one transmitter on the first speaker and the receiver’s ME Mic near the second speaker, or use two transmitters so each person wears a microphone. The right choice depends on where the speakers are positioned and whether both need freedom to move.

This guide is for YouTube creators and podcasters planning an interview, conversation, or two-person video. It explains what the Single and Dual sets contain, how to place each microphone, when to use Merged or Split mode, and how to verify the recorded channels before the real take.

The Single Set has one transmitter and one receiver. The receiver also contains the ME Mic, which is off by default. The Dual Set has two transmitters and one receiver. RØDE documents these configurations and the receiver microphone in the Wireless ME user guide, accessed September 20, 2026.

Choose one transmitter plus ME Mic when the second person will remain near the receiver, often behind the camera. Choose two transmitters when both people need a microphone attached to them or will move away from the receiver.

Use one transmitter plus ME Mic for a two-way interview

The Single Set can capture two people because both TX and RX contain microphones. Clip the transmitter to the person in front of the camera. Position the receiver so its built-in ME Mic faces the second speaker and remains close enough for the intended shot.

RØDE demonstrates this arrangement in its iPhone two-way interview guide. The example aims the receiver microphone at the person behind the camera while the transmitter is clipped to the person in front. This setup fits an interviewer operating the camera and a guest appearing on screen.

It is less suitable when both speakers sit far from the camera or walk independently. ME Mic stays with the receiver, so its distance from the second speaker changes if the camera or interviewer moves. In that situation, two wearable transmitters provide more consistent placement.

Do not describe the Single Set as a two-transmitter system. It contains one TX. The second audio source in this workflow is the microphone built into RX.

Enable ME Mic and choose the output mode

ME Mic is disabled by default. Connect the receiver to RØDE Central, then enable the receiver microphone. RØDE’s Wireless ME configuration instructions identify ME Mic as the control for recording the person near the receiver.

Next, choose how the two sources reach the recording device:

Merged combines the active transmitter and receiver microphones into one summed output.
Split places the transmitter and receiver microphone on separate left and right channels.

RØDE lists Merged as the default and documents both options in its Merged and Split mode instructions. Use Merged when a ready-to-use combined track is more important than changing each speaker independently later.

Use Split when the recorder or app preserves stereo and you want separate control in editing. In the one-TX plus ME Mic arrangement, RØDE assigns the transmitter to the left channel and ME Mic to the right. Confirm that assignment with a test file because a mono recording mode may combine or discard the channel separation.

Have the guest speak alone, then the interviewer. Inspect the left and right meters or waveforms in the intended editor. If both voices appear together on each side, check whether Wireless ME is still in Merged mode or whether the destination converted the input to mono.

Give each speaker a transmitter when both need mobility

The Wireless ME Dual package includes two transmitters and one receiver. RØDE’s Wireless ME Dual product page presents the two-transmitter set for recording multiple subjects and documents output to cameras through 3.5 mm or to phones and computers through USB.

Clip one transmitter to each speaker. Keep placement similar so one person does not sound much farther away solely because the microphones sit at different distances. Secure each unit or compatible lavalier cable so clothing does not rub across the microphone during normal movement.

For two independently adjustable voices, disable ME Mic and choose Split mode. This keeps the receiver microphone from becoming an unnecessary third source and lets the two transmitter signals occupy separate output channels. Verify that the destination records stereo before relying on that separation.

If separate editing is unnecessary, Merged mode combines the two transmitters into a summed output. This is simpler to deliver, but the speakers cannot be rebalanced independently after they have been combined. Correct microphone placement and test levels before the take.

Pair a second transmitter when expanding a Single Set

A Wireless ME receiver can pair with up to two compatible RØDE Series IV transmitters. RØDE documents the two-transmitter limit and pairing controls in the Wireless ME pairing guide.

Open RØDE Central with RX connected, power on the transmitter being added, and put that transmitter into pairing mode with a short press of its button. In RØDE Central, use the pair control under TX1 or TX2. Confirm that both transmitter connections remain solid before recording.

Check current compatibility in the user guide before buying a transmitter separately. The simplest packaged route is Wireless ME Dual because its two transmitters and receiver are supplied as one set and paired out of the box.

Do not assume that every RØDE transmitter or another brand’s transmitter can fill the second slot. Use a model RØDE documents as compatible with the Wireless ME receiver.

Understand what Merged and Split actually preserve

Merged mode is convenient when the destination or editing workflow expects one combined track. All active Wireless ME sources are summed. A louder speaker, poor placement, or unwanted receiver sound becomes part of that combined result and cannot be isolated as cleanly afterward.

Split mode provides two output channels, not an unlimited set of isolated tracks. With two active sources, it can place one source on the left and the other on the right for independent adjustment. The camera, phone, computer, or recorder must preserve that stereo input, and the editor must separate or pan the channels appropriately.

Test the complete signal path. Some recording configurations may save a mono file even when the receiver outputs Split channels. Record Speaker 1 alone, Speaker 2 alone, then both together. Open the file in the same editor planned for the production and confirm which waveform responds to each voice.

Three active microphones do not produce three isolated channels

Wireless ME Dual can capture its two transmitters and the receiver’s ME Mic at the same time. RØDE describes this as three microphones captured by the Dual system. That does not mean the receiver outputs three isolated tracks.

The user guide states that when two transmitters are paired and ME Mic is enabled in Split mode, both transmitters are summed to the left channel and ME Mic goes to the right. In Merged mode, all three active sources are summed into one combined output.

That routing has a practical consequence. If the goal is separate control over two interview subjects, turn ME Mic off and use one transmitter per person in Split mode. Enabling a third microphone would combine the two wearable transmitters on one side, removing their independent adjustment.

Use all three microphones only when that grouping fits the production. For example, the two wearable subjects can share the summed transmitter channel while the camera operator remains on the separate ME Mic channel. Label the channels before editing so the routing is not mistaken for three independent recordings.

Connect and verify the destination recording

The receiver sends the final routed audio to the recording device. RØDE documents USB-C output for phones and computers and a 3.5 mm output for cameras and other audio devices in the Wireless ME connection overview. Follow the destination-specific cable instructions rather than improvising an adapter chain.

A paired wireless link does not prove that the destination selected Wireless ME or started recording. Watch the camera or app meter while each person speaks. Then save and play back a sample from the destination itself.

Use this test sequence:

Ask Speaker 1 to talk while Speaker 2 stays silent.
Confirm the expected channel or combined meter responds.
Ask Speaker 2 to talk while Speaker 1 stays silent.
Confirm the second channel or combined meter responds.
Have both people speak naturally and check for overlap, level differences, and clothing noise.
Play back the saved file and inspect its channels in the intended editor.

Repeat the test after changing Merged, Split, ME Mic, pairing, or the destination recording mode. A setting stored in RØDE Central can persist when RX is moved to another camera, phone, or computer, according to the user guide.

Two-person recording checklist

Confirm whether the kit has one transmitter or two.
Use one TX plus ME Mic only when the second speaker can remain near RX.
Use two transmitters when both people need wearable microphones.
Enable ME Mic in RØDE Central only when the receiver-side speaker should be recorded.
Choose Merged for a combined output or Split for two output channels.
Disable ME Mic when two transmitters need independent left and right channels.
Confirm both transmitters are paired before a Dual setup.
Verify that the destination preserves stereo before relying on Split mode.
Record each person alone, then both together.
Play back the saved file and inspect its channels before the real take.

Wireless ME supports both a compact interviewer-and-guest setup and a two-wearable-microphone setup. The important tradeoff is microphone placement versus hardware count. For related planning, see whether RØDE Wireless ME has onboard recording and how to connect Wireless ME to an iPhone. Sharkjets Gear’s creator recording guides cover adjacent connection and backup decisions.